Configuring YAF with SiLK

This tutorial is a step-by-step guide for setting up yaf, and SiLK on a single machine for standalone Flow collection and analysis.

Install prerequisites

$ yum groupinstall "Development Tools"
$ yum install libpcap libpcap-devel pcre pcre-devel glib2-devel

Build libfixbuf:

$ tar -xvzf libfixbuf-2.3.0.tar.gz
$ cd libfixbuf-2.3.0
$ ./configure
$ make
$ make install

Build yaf:

$ tar -xvzf yaf-2.13.0.tar.gz
$ cd yaf-2.13.0
$ ./configure --enable-applabel --enable-plugins
$ make
$ make install

To run yaf as a service:

$ cp etc/init.d/yaf /etc/init.d/
$ cp etc/yaf.conf /usr/local/etc/
$ chmod +x /etc/init.d/yaf

Build SiLK:

$ tar -xvzf silk-3.19.0.tar.gz
$ cd silk-3.19.0
$ ./configure --with-libfixbuf=/usr/local/lib/pkgconfig --enable-ipv6
$ make
$ make install

Setup SiLK

This example uses /data as the location of the SiLK repository:

$ mkdir -p /data

The default silk.conf that comes with the SiLK distribution is typically sufficient and should be copied to the repository:

$ cp site/twoway/silk.conf /data

To run rwflowpack as a service:

$ cp src/rwflowpack/rwflowpack.init.d /etc/init.d/rwflowpack
$ chmod +x /etc/init.d/rwflowpack
$ cp src/rwflowpack/rwflowpack.conf /usr/local/etc/rwflowpack.conf

To configure rwflowpack, edit /usr/local/etc/rwflowpack.conf

#/usr/local/etc/rwflowpack.conf
ENABLED=1
statedirectory=/var/lib/rwflowpack
CREATE_DIRECTORIES=yes
BIN_DIR=/usr/local/sbin
SENSOR_CONFIG=/data/sensor.conf
DATA_ROOTDIR=/data
SITE_CONFIG=/data/silk.conf
PACKING_LOGIC=
INPUT_MODE=stream
INCOMING_DIR=${statedirectory}/incoming
ARCHIVE_DIR=${statedirectory}/archive
FLAT_ARCHIVE=0
ERROR_DIR=  #${statedirectory}/error
OUTPUT_MODE=local
SENDER_DIR=${statedirectory}/sender-incoming
INCREMENTAL_DIR=${statedirectory}/incremental
COMPRESSION_TYPE=
POLLING_INTERVAL=
FLUSH_TIMEOUT=
FILE_CACHE_SIZE=
FILE_LOCKING=1
PACK_INTERFACES=0
LOG_TYPE=syslog
LOG_LEVEL=info
LOG_DIR=${statedirectory}/log
PID_DIR=${LOG_DIR}
USER=root
EXTRA_OPTIONS=

The sensor.conf is required to setup the listening probe. Change the internal-ipblocks to match your network

probe S0 ipfix
   listen-on-port 18001
   protocol tcp
end probe

sensor S0
   ipfix-probes S0
   internal-ipblocks 192.168.1.0/24 10.10.10.0/24
   external-ipblocks remainder
end sensor

Move the sensor.conf to the repository:

$ mv sensor.conf /data

Start rwflowpack with the appropriate command:

$ systemctl start rwflowpack

or

$ service rwflowpack start

Verify that rwflowpack is listening on port 18001:

$ netstat -vnatpl

To use the SiLK command line tools, you need to set the SILK_DATA_ROOTDIR variable:

$ export SILK_DATA_ROOTDIR=/data

Configure YAF

Create a directory for the yaf log file:

$ mkdir /var/log/yaf
$ mkdir /var/log/yaf/log
$ mkdir /var/log/yaf/run

$ export LTDL_LIBRARY_PATH=/usr/local/lib/yaf

To configure yaf, edit the configuration file /usr/local/etc/yaf.conf:

ENABLED=1
YAF_CAP_TYPE=pcap
YAF_CAP_IF=eth0
YAF_IPFIX_PROTO=tcp
YAF_IPFIX_HOST=localhost
YAF_IPFIX_PORT=18001
YAF_STATEDIR=/var/log/yaf
YAF_EXTRAFLAGS="--silk --applabel --max-payload=2048 --plugin-name=/usr/local/lib/yaf/dpacketplugin.la"

Start YAF

Either start YAF via service via systemctl or service:

systemctl start yaf

service yaf start

Or on the command line. See the following 2 examples.

Example yaf command line for processing a PCAP file:

/usr/local/bin/yaf
--in <PCAP FILE> \
--ipfix tcp \
--out localhost \
--log /var/log/yaf/yaf.log \
--verbose \
--silk \
--verbose \
--ipfix-port=18001 \
--applabel --max-payload 2048 \
--plugin-name=/usr/local/lib/yaf/dpacketplugin.so

Example yaf command line for sniffing interface eth0:

/usr/local/bin/yaf
--in eth0 --live pcap \
--ipfix tcp \
--out localhost \
--log /var/log/yaf/yaf.log \
--verbose \
--silk \
--verbose \
--ipfix-port=18001 \
--applabel --max-payload 2048 \
--plugin-name=/usr/local/lib/yaf/dpacketplugin.so

If you see an error similar to:

Starting yaf: /usr/local/bin/yaf: error while loading shared
libraries: libairframe-2.5.0.so.4: cannot open shared object file:
No such file or directory
[Failed]

Run:

$ ldconfig

Or add /usr/local/lib to the LD_LIBRARY_PATH environment variable.

Confirm SiLK is creating flow records:

$ rwfilter --proto=0- --type=all --pass=stdout | rwcut | head